ServicesHigh Speed Doors
High Speed Door Repair in Weatherly
When a high speed door stalls, reverses for no reason or loses its curtain to a forklift, traffic and temperature control both suffer. We find what actually failed, whether that's the sensor, the drive, the curtain or the control settings, then repair it properly.
Fast doors fail in specific ways
A high speed door cycles hundreds of times a shift, far more than a standard overhead door. That pace exposes small problems quickly. A dirty photo eye, a drifting encoder or a curtain edge pulled out of its guide can look like a dead motor, and replacing the wrong part only adds cost and downtime.
We service fabric roll-up doors, self-repairing breakaway curtains and rigid spiral doors used at warehouse interiors, freezer and cooler openings, and exterior dock entries. Before we touch a part, we read the fault history on the drive, watch the door cycle and check each input. You get a clear explanation of the cause and a written estimate for the repair.
What our high speed door service covers
- 01
Curtain reset and replacement
Breakaway curtains are built to release on impact and re-feed into the guides. We reset them, repair torn zipper edges and replace curtain panels or the full curtain when the fabric has worn through or stretched out of shape.
- 02
Drive and control diagnosis
Most fast doors run on a variable frequency drive with an encoder that sets the open and close positions. We read stored fault codes, check motor and brake function, and recalibrate limits that have drifted so the door stops where it should.
- 03
Activation and safety devices
We test and align photo eyes, light curtains, motion radar, pull cords and floor loops. Reversing edges and safety beams get particular attention, because a door this fast needs to stop and reverse reliably when someone steps into the opening.
- 04
Guides, columns and seals
Bent side columns, worn brush seals and damaged bottom bars are common after impacts. We straighten or replace them so the curtain tracks cleanly and the opening seals against drafts.
- 05
Freezer and cooler door care
On cold-room doors we check heated guides, insulated curtain sections and seal contact, since frost buildup is a frequent cause of jams and slow travel.
- 06
Interlocks with dock equipment
Where a fast door is wired to a dock leveler or vehicle restraint, we confirm the interlock logic works so the door, the trailer and the dock act in the right order.
Questions about High Speed Doors?
Call(570) 989-8869Signs your high speed door needs attention
It reverses without a reason
A door that opens again halfway down usually points to a misaligned photo eye, a failing light curtain or a sensitive edge sending a false signal.
Slower travel than it used to have
Sluggish opening or closing can come from drive settings, a dragging brake or curtain friction in the guides. Each has a different fix, which is why we check before replacing anything.
The curtain won't re-feed after a hit
Breakaway designs should recover on their own or with a simple reset. If the curtain stays out of the guide, the edge or the guide itself is likely damaged.
Fault codes on the control panel
Repeated codes are a record of what the door is struggling with. Note them if you can, and we will read the full history on site.
Drafts, frost or temperature loss
In winter, an exterior fast door that no longer seals well lets cold air into the building and pushes up heating costs. On freezer doors, frost on the guides is an early warning.
How a service visit runs
- 1
A conversation by phone
You tell us the door type, what it's doing and when it started. That helps us bring the right test equipment and likely parts on the first trip.
- 2
Diagnosis on site
We watch the door cycle, pull fault data from the drive and test each sensor and safety device. We show you what we found and explain the cause in plain terms.
- 3
Written estimate
You get a line-item estimate covering parts and labor. If a repair makes more sense than replacement, we say so, and if the door is past repairing, we explain why.
- 4
Repair around your operation
We plan the work to limit downtime, often between shifts or during slower receiving windows. The opening is coned off while we work, and we clean up before we leave.
- 5
Test and hand back
We run the door through repeated cycles, confirm the safety reversal and interlocks, and walk your team through anything that changed.
What affects the cost of high speed door repair
The price depends far more on what failed than on the door itself. A sensor realignment is a short visit, while a new curtain or drive component involves parts and more labor. Accurate diagnosis keeps the estimate focused on the real problem.
- Door type and size
- Fabric roll-up doors, breakaway curtains and rigid spiral doors use different parts. Taller and wider openings need larger curtains and more lift time.
- The failed component
- Curtains, drives, encoders, motors and control boards vary widely in cost and lead time. Some parts are stocked by suppliers, others are made to order.
- Impact damage
- A forklift strike can bend columns and bottom bars as well as the curtain. We price each damaged piece separately so you can see where the cost comes from.
- Access and scheduling
- Work at height, tight aisles or cold-room conditions add time. Repairs scheduled outside operating hours may also affect the estimate.
High speed door questions
A forklift knocked our curtain out. Can it just be reset?
Often, yes. Breakaway curtains are designed for that. If the zipper edge is torn or the guide is bent, though, a reset won't hold and the curtain will keep coming out. We inspect both before deciding.
Can you work on a door another company installed?
In most cases, yes. We start by identifying the drive and controls and confirming parts are available for that model. If a part is hard to source, we tell you up front and explain the options.
Our door keeps reversing. Is the motor failing?
Usually not. False reversals are far more often caused by a dirty or misaligned photo eye, a light curtain fault or a worn reversing edge. Those are much simpler repairs than a motor, which is why we test the sensors first.
Can you do the work without shutting down our dock?
We plan around your schedule and can often work between shifts or during slow periods. The door itself has to be out of service while we repair it, but we keep that window as short as the job allows.
Should we replace our old fast door instead of repairing it?
It depends on the condition of the drive, the availability of parts and how often it fails. We give you an honest read after the diagnosis. If replacement makes sense, our loading dock equipment installation and sales pages cover how that works.
Get the real cause of your door problem
Describe what your high speed door is doing and we will arrange a visit to find out why. We serve facilities in Weatherly and nearby towns including Hazleton, Lehighton and Jim Thorpe.